Chat with us, powered by LiveChat

PEEK MT – Natural
(TECAPEEK MT – Natural)

Main features

  • high creep resistance
  • very good stress cracking resistance
  • good machinability
  • resistance against high energy radiation
  • very good chemical resistance
  • hydrolysis and superheated steam resistant
  • good slide and wear properties
  • very good sterilisable

To view PEEK MT – Natural
(TECAPEEK MT – Natural) mechanical properties, thermal properties, electrical properties, other properties, specifications or shapes & sizes please click on the tabs below.

Colour:
Colour Code
This product appears in: , ,

Get a Quote Call Us Email Us
Rounds (mm)
5
6
8
10
12
15
16
18
20
22
25
28
30
32
36
40
45
50
56
60
65
70
80
90
100
110
120
125
140
150
160
165
180
200
Plate (mm)
5
6
8
10
12
16
18
20
25
30
36
40
45
50
120

Our information and statements reflect the current state of our knowledge and shall inform about our products and their applications. They do not assure or guarantee chemical resistance, quality of products and their merchantability in a legally binding way. Our products are not defined for use in medical or dental implants. Existing commercial patents have to be observed. The corresponding values and information are no minimum or maximum values, but guideline values that can be used primarily for comparison purposes for material selection. These values are within the normal tolerance range of product properties and do not represent guaranteed property values. Therefore they shall not be used for specification purposes. Unless otherwise noted, these values were determined by tests at reference dimensions (typically rods with diameter 40-60 mm according to DIN EN 15860) on extruded and machined specimen. As the properties depend on the dimensions of the semifinished products and the orientation in the component (esp. in reinforced grades), the material may not be used without a separate testing under individual circumstances. The customer is solely responsible for the quality and suitability of products for the application and has to test usage and processing prior to use. Technical changes reserved.

Chemical Designation

PEEK (Polyetheretherketone)

Colour

natural opaque

Density

1.31 g/cm3

Our information and statements reflect the current state of our knowledge and shall inform about our products and their applications. They do not assure or guarantee chemical resistance, quality of products and their merchantability in a legally binding way. Our products are not defined for use in medical or dental implants. Existing commercial patents have to be observed. The corresponding values and information are no minimum or maximum values, but guideline values that can be used primarily for comparison purposes for material selection. These values are within the normal tolerance range of product properties and do not represent guaranteed property values. Therefore they shall not be used for specification purposes. Unless otherwise noted, these values were determined by tests at reference dimensions (typically rods with diameter 40-60 mm according to DIN EN 15860) on extruded and machined specimen. As the properties depend on the dimensions of the semifinished products and the orientation in the component (esp. in reinforced grades), the material may not be used without a separate testing under individual circumstances. The customer is solely responsible for the quality and suitability of products for the application and has to test usage and processing prior to use. Technical changes reserved.

Mechanical properties parameter value unit norm  
Modulus of elasticity(tensile test) 1mm/min

4200

MPa

 DIN EN ISO 527-2 1)
Tensile strength 50mm/min

116

MPa

 DIN EN ISO 527-2  
Tensile strength at yield 50mm/min

116

MPa

 DIN EN ISO 527-2  
Elongation at yield 50mm/min

5

%

 DIN EN ISO 527-2  
Elongation at break 50mm/min

15

%

 DIN EN ISO 527-2  
Flexural strength 2mm/min, 10 N

175

MPa

 DIN EN ISO 178 2)
Modulus of elasticity (flexural test) 2mm/min, 10 N

4200

MPa

 DIN EN ISO 178  
Compression strength 1% / 2% 5mm/min, 10 N

23 / 43

MPa

 EN ISO 604 3)
Compression modulus 5mm/min, 10 N

3400

MPa

 EN ISO 604 4)
Impact strength (Charpy) max. 7,5J

n.b.

kJ/m2

 DIN EN ISO 179-1eU 5)
Notched impact strength (Charpy) max. 7,5J

4

kJ/m2

 DIN EN ISO 179-1eA  
Ball indentation hardness  

253

MPa

 ISO 2039-1 6)

(1) For tensile test: specimen type 1b
(2) For flexural test: support span 64mm, norm specimen.
(3) Specimen 10x10x10mm
(4) Specimen 10x10x50mm, modulus range between 0.5 and 1% compression.
(5) For Charpy test: support span 64mm, norm specimen. n.b. = not broken
(6) Specimen in 4mm thickness

Our information and statements reflect the current state of our knowledge and shall inform about our products and their applications. They do not assure or guarantee chemical resistance, quality of products and their merchantability in a legally binding way. Our products are not defined for use in medical or dental implants. Existing commercial patents have to be observed. The corresponding values and information are no minimum or maximum values, but guideline values that can be used primarily for comparison purposes for material selection. These values are within the normal tolerance range of product properties and do not represent guaranteed property values. Therefore they shall not be used for specification purposes. Unless otherwise noted, these values were determined by tests at reference dimensions (typically rods with diameter 40-60 mm according to DIN EN 15860) on extruded and machined specimen. As the properties depend on the dimensions of the semifinished products and the orientation in the component (esp. in reinforced grades), the material may not be used without a separate testing under individual circumstances. The customer is solely responsible for the quality and suitability of products for the application and has to test usage and processing prior to use. Technical changes reserved.

Thermal properties parameter value unit norm  
Glass transition temperature  

150

°C

 DIN 53765 1)
Melting temperature  

342

°C

 DIN 53765  
Service temperature short term

300

°C

   2)
Service temperature long term

260

°C

    
Thermal expansion (CLTE) 23-60°C, long.

5

10-5 K-1

 DIN EN ISO 11359-1;2  
Thermal expansion (CLTE) 23-100°C, long.

5

10-5 K-1

 DIN EN ISO 11359-1;2  
Thermal expansion (CLTE) 100-150°C, long.

7

10-5 K-1

 DIN EN ISO 11359-1;2  
Specific heat  

1,1

J/(g*K)

 ISO 22007-4:2008  
Thermal conductivity  

0,27

W/(K*m)

 ISO 22007-4:2008  

(1) Found in public sources.
(2) Found in public sources. Individual testing regarding application conditions is mandatory.

Our information and statements reflect the current state of our knowledge and shall inform about our products and their applications. They do not assure or guarantee chemical resistance, quality of products and their merchantability in a legally binding way. Our products are not defined for use in medical or dental implants. Existing commercial patents have to be observed. The corresponding values and information are no minimum or maximum values, but guideline values that can be used primarily for comparison purposes for material selection. These values are within the normal tolerance range of product properties and do not represent guaranteed property values. Therefore they shall not be used for specification purposes. Unless otherwise noted, these values were determined by tests at reference dimensions (typically rods with diameter 40-60 mm according to DIN EN 15860) on extruded and machined specimen. As the properties depend on the dimensions of the semifinished products and the orientation in the component (esp. in reinforced grades), the material may not be used without a separate testing under individual circumstances. The customer is solely responsible for the quality and suitability of products for the application and has to test usage and processing prior to use. Technical changes reserved.

Electrical properties parameter value unit norm  
Specific surface resistance  

1014

Ω

 DIN IEC 60093  
Specific volume resistance  

1014

Ω*cm

 DIN IEC 60093  

(1) Specimen in 20mm thickness
(2) Specimen in 1mm thickness

Our information and statements reflect the current state of our knowledge and shall inform about our products and their applications. They do not assure or guarantee chemical resistance, quality of products and their merchantability in a legally binding way. Our products are not defined for use in medical or dental implants. Existing commercial patents have to be observed. The corresponding values and information are no minimum or maximum values, but guideline values that can be used primarily for comparison purposes for material selection. These values are within the normal tolerance range of product properties and do not represent guaranteed property values. Therefore they shall not be used for specification purposes. Unless otherwise noted, these values were determined by tests at reference dimensions (typically rods with diameter 40-60 mm according to DIN EN 15860) on extruded and machined specimen. As the properties depend on the dimensions of the semifinished products and the orientation in the component (esp. in reinforced grades), the material may not be used without a separate testing under individual circumstances. The customer is solely responsible for the quality and suitability of products for the application and has to test usage and processing prior to use. Technical changes reserved.

Other properties parameter value unit norm  
Water absorption 24h / 96h (23°C) 0.02 /0.03 % DIN EN ISO 62 1)
Resistance to hot water/ bases   +   – 2)
Resistance to weathering   –   – 3)
Flammability (UL94) listed (value at 1.5mm) V0   DIN IEC 60695-11-10  

(1) Ø ca. 50mm, h=13mm
(2) (+) limited resistance
(3) - poor resistance
(4) Corresponding means no listing at UL (yellow card). The information might be taken from resin, stock shape or estimation. Individual testing regarding application conditions is mandatory.

Our information and statements reflect the current state of our knowledge and shall inform about our products and their applications. They do not assure or guarantee chemical resistance, quality of products and their merchantability in a legally binding way. Our products are not defined for use in medical or dental implants. Existing commercial patents have to be observed. The corresponding values and information are no minimum or maximum values, but guideline values that can be used primarily for comparison purposes for material selection. These values are within the normal tolerance range of product properties and do not represent guaranteed property values. Therefore they shall not be used for specification purposes. Unless otherwise noted, these values were determined by tests at reference dimensions (typically rods with diameter 40-60 mm according to DIN EN 15860) on extruded and machined specimen. As the properties depend on the dimensions of the semifinished products and the orientation in the component (esp. in reinforced grades), the material may not be used without a separate testing under individual circumstances. The customer is solely responsible for the quality and suitability of products for the application and has to test usage and processing prior to use. Technical changes reserved.

Can we help?



Dublin HQ and Engineering Plastics Office

76 Cookstown Ind. Estate, Tallaght, Dublin 24, Ireland
Eircode: D24 AF84
Tel: +353 1 451 2144, Fax: +353 1 451 5405
Email: kevincondon@impactirl.ie

Cork Office

Brooklodge, Glanmire, Co. Cork, Ireland
Eircode: T45 KX01
Tel: +353 21 486 6006, Fax: +353 21 486 6326
Email: brianpower@impactirl.ie

Belfast Office

17 Sentry Lane, Antrim Road, Newtownabbey
BT36 4XY, NI
Tel: +44 28 9084 2223, Fax: +44 28 9084 2133
Email: richardgawley@impactirl.ie

Export Sales

Impact Special Metals
76 Cookstown Ind. Estate, Tallaght, Dublin 24, Ireland
Tel: +353 1 451 2144, Fax: +353 1 451 5405
Email: liamvickers@impactirl.ie